top of page

Groups Feed

View groups and posts below.


This post is from a suggested group

Bleeding gums when brushing

My gums bleed almost every time I brush and floss. It doesn't hurt, but it's been going on for a few weeks. Is it gingivitis? Should I see a dentist or try a different toothpaste first?

10 Views
Guest
Guest
Nov 10

Bleeding gums are most often early gingivitis from plaque along the gum line, and the good news is it's usually reversible. Brush gently twice a day with a soft brush and floss daily even if it bleeds at first, it should improve within a week or two. If it keeps bleeding after that, or you notice swelling, bad breath or receding gums, book a cleaning since tartar can only be removed professionally. I had the same issue and went to a dental clinic Pickering for a deep cleaning, and after that, flossing properly kept it under control. Don't put it off, untreated gum disease can lead to bone loss.

This post is from a suggested group

Managing a small apartment building

We own a 12 unit building in the Mission and have been self managing, but it's becoming a second job. Vacancies, repairs, late rent. For those who switched to a management company, did it actually help or did you lose control?

10 Views

We switched at 10 units and it was the right call. You do give up some day to day control, but you set the rules up front, like approval limits for repairs and how tenants are screened. Ours needs our approval for anything over a set amount. The biggest improvements for us were faster turnover of vacant units and having someone on call at night. Make sure they know SF rent control and the required notices. We went with apartment management in San Francisco from a firm that specializes in older multi unit buildings. Review the first few months closely and you'll know quickly if they're a good fit.

This post is from a suggested group

Best time of year to replace windows

We need to replace most of the windows in our house in Edmonton. Is it a bad idea to do it in winter, or should we wait until spring? Worried about heat loss during the install.

7 Views
Guest
Guest
Nov 10

It can be done in winter, installers here do it all the time. They usually swap one window at a time, so each opening is only exposed for a short while and the house doesn't get very cold. Some foams and sealants need a minimum temperature though, so ask how they handle that. The bigger issue is booking. Spring and summer are the busiest seasons, so lead times can be long. We ordered in February and had the install in late March. If you're looking at window replacement Edmonton companies, ask for the exact product specs, warranty and how they finish the interior trim. Get the old frames checked for rot before ordering.

This post is from a suggested group

Hood cleaning for a small cafe

I run a small cafe with a little hood over a panini press and a two burner range. Does a place this size really need professional hood cleaning? It seems like overkill for the amount of cooking we do.

7 Views
Florence
Florence
Nov 10

Light cooking still produces grease vapour, it just builds up slower. For a cafe like yours it's usually every six months to a year, and your fire inspector or insurance company will probably ask for proof it was done. Clean the filters weekly, that's easy to do yourself in the sink with a degreaser. For the full service, kitchen hood cleaning in Toronto doesn't take long for a small setup, usually a couple of hours after closing. Keep the service reports in a binder, the inspector asked for ours on the first visit. It's cheap compared to dealing with a fire or a failed inspection.

This post is from a suggested group

Why would anyone buy a junior explorer

Everyone says junior mining stocks are risky and most never make money. So why do people still invest in them? What's the case for holding a small explorer instead of a big producer?

7 Views

The case is mostly about leverage to discovery. A big producer's value is already priced on its existing mines, so a new find barely moves it. For a small explorer, one good drill result can rerate the whole company, and if a major buys it out, early holders can do very well. The flip side is that many explorers never find an economic deposit and keep raising money, which dilutes shareholders. People who invest in them usually treat it as a small, high risk part of a portfolio. Before buying, read the company's own pitch, for example Rio Silver’s investment overview, and then compare it against the technical reports and cash position. Spread money across a few names rather than betting on one.

This post is from a suggested group

Which Cabo beaches are safe to swimWhich Cabo beaches are safe to swim

Planning to buy something in the Cabo area but I really want to be able to walk to a beach where you can actually swim. I've heard a lot of beaches there have dangerous currents. Which areas are best for that?

7 Views

You heard right, much of the Pacific side has strong currents and red flags most of the time. The safer swimming beaches are mostly on the Sea of Cortez side and inside the bay. Medano Beach in Cabo San Lucas is the main swimmable one and it's very busy. Along the Corridor, Santa Maria and Chileno are calm coves with good snorkeling, and Palmilla also has calm water. Properties within walking distance of those are limited and priced higher. There's a guide on where to look near swimmable beaches in Cabo that lists the neighborhoods close to each one, which helped us narrow it down. Always check the flags though, even calm beaches change with the swell.

This post is from a suggested group

Looking for a dentist in Miami

Just moved to Miami for work and need to find a new dentist. I'm due for a cleaning and I have a crown that's been feeling a little off. Ideally somewhere that takes PPO insurance and can do both general and restorative work in the same place. Any recommendations?

7 Views

Welcome to Miami. When I moved here I called a few offices and asked right away if they take my plan and whether they do crowns in house or refer out, which narrowed it down fast. A lot of places only do cleanings and send you elsewhere for anything bigger. I ended up at Dental Team’s Miami office and they handled my cleaning and a crown replacement without sending me anywhere else. The front desk checked my insurance before the appointment, which saved me a surprise bill. For the crown, don't wait too long if it feels loose or sensitive, mine had a small gap under the edge that was starting to cause decay. Bring your old X rays if you have them.

This post is from a suggested group

Gas or wood fireplace for an older house

We bought a 1970s bungalow in south Edmonton and the living room has an old brick wood fireplace that hasn't been used in years. Thinking about converting it to gas or putting in an insert. Has anyone done this? Mostly wondering about cost, heat output and whether it's worth the hassle for winter.

7 Views

We did almost the same thing two winters ago. Our chimney needed relining anyway, so a gas insert ended up making more sense than fixing the wood setup. The heat difference is huge, the old open fireplace was basically pulling warm air out of the room. I'd get the chimney inspected first, then go look at units in person because the sizes and face options vary a lot. We went to Barbecues Galore’s south Edmonton store and they had several inserts running so you could actually feel the output. Budget for installation and venting separately, that was about half our total. Also ask about a blower, it makes a big difference in a larger room.

This post is from a suggested group

Manufacturing cost accounting and inventory control

Rising raw material prices and supply chain delays are making it really hard for our manufacturing plant to keep track of true COGS and factory overhead absorption. We need a better way to price our product lines without hurting gross margins. What frameworks do manufacturers use to optimize inventory and production planning?

8 Views

Unpredictable material prices and supply chain delays kept throwing off our shop floor cost calculations and gross margin targets. We partnered with US Fractional CFO Alliance https://usfractionalcfo.com/industry/manufacturing-cfo/ to fix our job-costing framework and streamline inventory valuation. It took the constant stress out of pricing big production orders.

Edited
bottom of page